# Capacitor code table

## European capacitor material codes

FKC = metal foil and polycarbonate
FKP = metal foil and polypropylene
MKC = metallized polycarbonate foil
MKI = metallized polyphenylene sulphide
MKP = metallized polypropylene
MKS = polystyrene (metallized or with foil)
MKT = metallized polyester foil

## Decoding capacitor codes

Looking at our capacitor we will see its marked 474J, this should be read as follows, 47 times the value that can be found in Table 1 corresponding to the 3rd number, in this case 10000. 47 * 10000 = 470000 pF = 470 nF = 0.47 uF with the J meaning a 5% tolerance. A second letter will be a temperature coefficient if its present. Judging by a capacitors size and type, you will quickly learn to determine if the value on the capacitor is given in pF, nF or uF.

If a capacitor is f.ex. marked 2A474J, the capacitance is decoded as described above, the two first signs is the voltage rating and can be decoded from table 2 here below. 2A is 100VDC rating according to the EIA standard.

Some capacitors are only marked 0.1 or 0.01, mostly in these cases the values are given in uF.

Some small capacitance capacitors can be marked with a R between numbers, f.ex. 3R9 where R is a indicator of values below 10pF and have nothing to do with resistance. 3R9 would be 3.9pF.

Table 1

 3rd number Multiply with Letter Tolerance 0 1 D 0.5pF 1 10 F 1% 2 100 G 2% 3 1,000 H 3% 4 10,000 J 5% 5 100,000 K 10% 6 1,000,000 M 20% 7 Not used M 20% 8 0.01 P +100%/-0% 9 0.1 Z +80%/-20%

Table 2 – Electronic Industries Alliance (EIA) – voltage code table

 0G = 4.0VDC 0L = 5.5VDC 0J = 6.3VDC 1A = 10VDC 1C = 16VDC 1E = 25VDC 1H = 50VDC 1J = 63VDC 1K = 80VDC 2A = 100VDC 2Q = 110VDC 2B = 125VDC 2C = 160VDC 2Z = 180VDC 2D = 200VDC 2P = 220VDC 2E = 250VDC 2F = 315VDC 2V = 350VDC 2G = 400VDC 2W = 450VDC 2H = 500VDC 2J = 630VDC 3A = 1000VDC

Here is a list of common capacitors and a scale between the different grades of the Farad SI unit.

Table 3

 pico-farad (pF) nano-farad (nF) mikro-farad (mF,uF eller mfd) Capacitor code 1 0.001 0.000001 010 1.5 0.0015 0.0000015 1R5 2.2 0.0022 0.0000022 2R2 3.3 0.0033 0.0000033 3R3 3.9 0.0039 0.0000039 3R9 4.7 0.0047 0.0000047 4R7 5.6 0.0056 0.0000056 5R6 6.8 0.0068 0.0000068 6R8 8.2 0.0082 0.0000082 8R2 10 0.01 0.00001 100 15 0.015 0.000015 150 22 0.022 0.000022 220 33 0.033 0.000033 330 47 0.047 0.000047 470 56 0.056 0.000056 560 68 0.068 0.000068 680 82 0.082 0.000082 820 pF nF uF Code 100 0.1 0.0001 101 120 0.12 0.00012 121 130 0.13 0.00013 131 150 0.15 0.00015 151 180 0.18 0.00018 181 220 0.22 0.00022 221 330 0.33 0.00033 331 470 0.47 0.00047 471 560 0.56 0.00056 561 680 0.68 0.00068 681 750 0.75 0.00075 751 820 0.82 0.00082 821 1000 1 or 1n 0.001 102 1500 1.5 or 1n5 0.0015 152 2000 2 or 2n 0.002 202 2200 2.2 or 2n2 0.0022 222 3300 3.3 or 3n3 0.0033 332 4700 4.7 or 4n4 0.0047 472 5000 5 or 5n 0.005 502 5600 5.6 or 5n6 0.0056 562 6800 6.8 or 6n8 0.0068 682 10000 10 or 10n 0.01 103 15000 15 or 15n 0.015 153 22000 22 or 22n 0.022 223 33000 33 or 33n 0.033 333 47000 47 or 47n 0.047 473 68000 68 or 68n 0.068 683 pF nF uF Code 100000 100 or 100n 0.1 104 150000 150 or 150n 0.15 154 200000 200 or 200n 0.20 204 220000 220 or 220n 0.22 224 330000 330 or 330n 0.33 334 470000 470 or 470n 0.47 474 680000 680 0.68 684 1000000 1000 1.0 105 1500000 1500 1.5 155 2000000 2000 2.0 205 2200000 2200 2.2 225 10000000 10000 10 106

### 395 Responses to Capacitor code table

please what is or are the values (uf) of microwave capacitor?
Also what is the wattage of the microwave transformer? please email me here: dejiola2001@aol.com
thanks you

Microwave oven capacitors are typically between 0,8 to 1,0 uF and a microwave oven transformer will be about 600 to 1300 Watt depending on the model.

3. hi, I have a capacitor marked with: 2J472J
now I understand that 472=4700, J = 5% tolerence. What is the 2J in the start??
and what is the tolerence??

Hey Usama

2J could be related to the manufacturer of the capacitor, nothing that will influence of what properties it has. Tolerance means that the given capacitance can be +/- 5% of the given value.

Kind regards

5. osama says:

now i can’t find a replacement for that 2J472J capacitor, can i use a different one instead?? if yes, what is the safe range of value?? a seller told me that the 474J can be a replacement, I know he can’t be serious..
thx again

You need to replace it with a 472 which is 4,7nF and a 474 is a 470nF, which is 100 times too large value for what you need.

7. osama says:

last question regarding this type of capacitors, is it polarized? and have negative and positive?? or its ok to install in any direction?? thanks buddy

Hey Osama

I am 99% sure that the capacitor you have is not polarized, polarized capacitors normally have other markings for the values and polarities are indicated.

Kind regards

9. osama says:

huge thanks buddy 😀

10. Dave says:

I had a 474J capacitor go bad (it looks like it blew up) in a Sony audio system and ordered new ones from eBay but I received 474K instead. So the tolerance is 10% instead of 5%. Will they still work? Should I let the guy know he sent me wrong ones?

Hey Dave

It really depends where in the circuit the capacitor is used, if it was in the signal path of the audio signal, sound could be different. If it is used in a RC circuit the time constant of this could change. If it was used as decoupling over a IC it properly does not matter.

Bottomline, I think you can change it without any problems, atleast you can always switch it off and install the correct ones if you find it acting up weird, the difference between 5% to 10% is afterall for a 474 only 20 nF.

Kind regards

12. Dave says:

Thanks for the reply. I have changed them (there were two of them) and it seems to work fine now, but then again I haven’t tested it very thoroughly to see if any of the things you mentioned could be happening. I think I’ll keep using it normally for now and if I don’t notice anything off when listening to it, then all the better.

PS. The problem it was doing before I fixed it was that it turned on and worked just fine, but it shut off automatically after a couple of minutes. Also, some burning smell could be present sometimes. The unit is a sound system and a 5-disc DVD player that came with my TV. Also, I was mistaken before, it’s Samsung, not Sony. Maybe you can tell me more with this extra information?

13. D says:

“6 and 7 not used”? Have tantalum cap in my hand: “106”

Hey D

I have updated the charts with this new standard, was capacitors get smaller, the writing also have to change.

Kind regards

15. Kevin says:

I’m trying to replace a capacitor. It’s shaped like a barrel, about a 1/2″ tall. On the top it has three lines:
470
V FK
6J9K

Any idea what I should replace it with?

Hey Kevin

470 is the rating in uF
V is the voltage rating, can only be decoded from the manufaturers datasheet.
FK is the type of capacitor
6J9K is the series lot number

It sounds like a electrolytic capacitor with a capacitance of 470 uF and a 35 VDC rating. That is taken from this datasheet, so be aware that if you have a different manufacturer, it could be other ratings. http://www.farnell.com/datasheets/58258.pdf

Kind regards

17. Rob says:

I found on a wiring schematic that a guitar needs a .047uf cap. Another site has all these different types of caps ranging from .00001 to 200. Whats the difference between all those and what would be the best one to use on a guitar? The capacitor is used for a tone knob on the guitar.

Hey Rob

I do not know much about guitars, but if the capacitor is part of a tone control it is likely to be part of a filter and you can then adjust that filter with the knob. Changing the capacitance to something else than the original will change the bandwidth of the tone knob, so it will work in a different spectrum.

Kind regards

19. David Annieya says:

i want to sent the pictures of my capacitors i want to buy and where i can get them. need about 1000 pieces { david14dastech@yahoo.com }

20. David Annieya says:

Hello David

Kind regards

22. fre says:

Someone said before about first numeric + second character in poly-film-cap is “could be related to the manufacturer of the capacitor…”
Recently seen in two caps – 2A102J & 2J102J ‘and’
same again seen in two caps – 2A103J & 2E103J
I think that’s is not related to manufacture/s coding system.. ‘and’
it’s may be related to the ‘voltage’ – which is confusing..
if some one knows better – please update

23. ss says:

2j222j,here what is 2j and how to determine the voltage

Hello SS

I have added a voltage rating table to the page. It is table 2 and gives the voltages according to the EIA standard.

Kind regards

25. ss says:

then what is the use of manufacturing data sheet?if 3j333j means how much voltage

Hey ss

Capacitance and voltage rating is really only a very few specifications for a capacitor, to insure reliable operation there is many other factors, some of which are f.ex. used in pulse operation can be seen here: http://kaizerpowerelectronics.dk/theory/good-mmc-capacitors/

Kind regards

27. ss says:

i dont understand what are you trying to say, http://kaizerpowerelectronics.dk/theory/good-mmc-capacitors/

28. sumit says:

225j 400v

29. sumit says:

i used other capacitor 225j400v

30. Andrew says:

Hello Sir,
I have a couple of capacitors I can’t decode.
First one is a Green looks like ceramic capacitor with the following:
0z //the “0” on this line is more like a tradmark with stuff in the center of the “0” i cant make out
683
50k
ncc
The second one is a blue covered, looks like ceramic again, with silver paint on the top. This one has the following on it:
1+
35z

//the “+” sign although it is next to the “1” is below a vertical white stripe which leads me to believe that sides pin is the positive pin and this is a polarized cap.

Thanks for any help.
Andrew

Hey Andrew

Pictures would help me more, but from your descriptions this is my best guess.

The first is a 68nF capacitor, voltage rating is uncertain.

The second sounds like a tantalum capacitor, which are polarized, 1uF and 35VDC rating.

Kind regards

32. Andrew says:

Where can i put up some images for you?
Andrew

Hey Andrew

You can use http://imgur.com/ f.ex. or any other free upload service.

Kind regards

34. Andrew says:

http://aunueget.imgur.com/
thanks for all the help
I just started uploading at the time of this post so it may need 30 min or so.
Andrew

Hey Andrew

You are welcome 🙂 You might have to set the pictures to be displayed public before I can see them.

Kind regards

36. Andrew says:

Sorry about that. I tested it; they should be public now.
Andrew

Hey Andrew

My answers remain the same, the second capacitor could be a polyester or polypropylene capacitor, if you need a similar, pick one with the same capacitance and a voltage rating higher than the supply voltage of the circuit.

Kind regards

38. Andrew says:

Thanks for all the help.
Andrew

39. RichT says:

Hi guys, I have a small (6mm diameter) blue disk capacitor blown on the o/p of an inverter circuit. The capacitor is blue and marked with a “5” above a “.” and then “3KV”. I’m guessing the 3KV is the voltage rating but any ideas on the value? Thanks Richard

Hey Richard

From the physical size, voltage rating and it being a ceramic disc capacitor, it could be given in pF as that is the case when just a 1 or 2 digit number is given, but 5 pF capacitor is very unlikely to have sitting across the output of an inverter. You are right about the 3kV being the voltage rating.

Kind regards

41. Yugal Kapoor says:

can i replace 474 j 100v capacitor with a 470 nk 100 v capacitor? i need it for my samsung 5.1 surround system. so, plz tell me if the latter one capacitor is a replacement of the 474 j 100 v…

Hello Yugal Kapoor

No, the first is a 0.47uF capacitor, if you look at the table above you will find that value at the 474 code. Code 470 is only 1/1000 of the capacitance.

You have the voltage rating correct, but you need a capacitor of the same capacitance to be sure of getting the same performance out of your speaker system. It could properly be substituted by another value, but still similar, +/- some 0.1uF depending on where in the circuit it is placed.

Kind regards

43. Gaétan Haché says:

Hi,
I need a 470pF 500v capacitor (at least 500v).
The surplus store sold me two capacitor — but I’m have doubt that I have the right ones.
One shows

MDC
68 J
N 470

and the other
470
+/- 20%
SEC

Both are disc caps about 5mm width,

Do I have the right one ?

Many thanks,
Gaetan Hache
Toronto

Gaetan Hache

470 is the code for 47pF, you need a code 471 for a 470pF capacitor. Disc capacitors are usually ceramic and for a 5 mm wide capacitor, 500V rating sounds reasonable, but do check manufacturers datasheet to be sure.

Kind regards

I have a Saab motor fan capacitor with markings
.15/20
1.50MKT
100v
I understand only that it is a Metalized Polyester file capacitor, rated up to 100 volts. What are the other numbers telling me about it?
Thank you,
Dave
Longmont, CO

Hey David

My best guess would be a 150nF (.15 uF) and 20% tolerance.

Kind regards

47. chris weller says:

can you tell me what is 0,033MK on a capacitor please is it the same as 0.33uf?

Hey chris weller

I would say it is a 0,033uF capacitor as it written on it, it is easier to tell from a picture of the capacitor in question. Even if you just find a similar picture on the internet.

Kind regards

49. Trevor allen says:

Hi
Can anyone help me identify a tiny non polarised blue bead capacitor with axial leads labelled
A 10 4Z.
trevor

Hey Trevor

My best guess without a picture would be a 100nF capacitor

Kind regards

hey guys i hav this brown n green capacitors r they same ?
they r written like 2A or 1K2 or 2Q or 3B what that means then 2n3 what that means

Refering to table 2 in this article: 2A = 100VDC and 2Q = 110VDC voltage rating. 3B is properly above 1kV. I guess that 2n3 is 2.3nF

Kind regards

very very thank you mads but looks what i did is in CFL i changeg 1250 volt 472J with 2A472j (that should be 100V 472J ) but it still working why?will it blow soon by over he or will shorten life of the tuben alos i tried 2G273J (400v273J) but didnt worked yes 273 is 10 times higher but shouldnt it worked better with high capacity
kindly waiting for ur experties oppinion

in polyester capacitor 1K2 mean 80*1.2 volt or 1.2kilovolt which is currect

in polyester capacitor 1K2 means 1.2*80 volt or 1.2 kilovolt?

The voltage rating could be so high, just to withstand the voltage spikes from the current switched by the transistor. It is not certain that manufacturers follow the marking standard, so you have to look at the datasheet from the manufacturer to be sure.

If the capacitor is used as part of a frequency forming network, it has to be the exact same capacitance, else the circuit might not work as you found out with a larger capacitor.

1K2 is voltage code for 1200VDC.

Kind regards

but above u mentioned 1K is 80 vDC how some one can say its 1200vdc or (80*1.2 )=96 VDC?
as one of my friend arguing as 2A332J as 2ampire 332j where i told him according to ur table 2A=100VDC

1K = 80VDC is only according to the Electronic Industries Alliance (EIA) – voltage code table standard. 1K2 is some bastard marking where the manufacturer uses the resistance markings for 1200 to write the voltage rating.

I have not yet seen a small capacitor with current markings, you can almost sure that a capacitor is marked with voltage rating, tolerance and capacitance.

As these examples show, there is not just one way to read the markings, there is many different ways and the only way to be sure is to find the manufacturers data sheet.

Kind regards

i think got every ans i need n yes yesterday whole night i hav been repairing my old compact fluorescent ballast (so called made in china – in my room only within 2 year i had to change 6 ,)so i decided to repair it any how n i repaired 3 of them
very very thank you mads .. think got every ans i needed so far as it just my hobby i learnt every thing about electronics by my self since i was -7 yrs old n even i am a medical doctor now i couldnt quit my hobby …..so thank again u made my day

61. mamata says:

what does 3n3J 1n5J 1n8J means also there Is something like 1n5/2J what does it means?

62. mamata says:

can you tell me the output voltage n /current on 40w cfb/cfl tubes just some rough idea n how bad it will shock if accidently touched

63. mamata says:

what metal is used in metallized polypropylene n what is that stuff comes out from it whicj looks like rubber or lead like stuff i hav sent u 3 questions hope u will send me some clear guidance thank you

64. Trevor Allen says:

I am not very good on using the internet.

I emailed you pictures of my Tiny Blue Capacitor labelled A 10 4Z, that you thought may be 100nF but needed a picture, AUG 16th. Did you recieve my photographs and my second e mail as I have not seen a reply since, sorry to trouble you, but I broke two of these and I need to replace them.
Kind regards
Trevor

65. ramesh says:

can we add 2 polyester cap in parallel to add-up its capacity ?
eg 2A222J +2A222J=2A442J OR IF THERE IS ANY FORMULA FOR IT

Hey manata

what does 3n3J 1n5J 1n8J means also there Is something like 1n5/2J what does it means? Look at the tables in this article and read the text, those corresponds to 3.3nF 5% tolerance and so on for the others.

The output voltage from a 40W CFL driver is roughly around 900 to 1000 Volt at some high frequency, using Ohms laws that is around 40mA.

Metallized polypropylene capacitors are likely to use aluminium or zinc for the metallization of the plastic film. The other stuff you find in a capacitor is then either plastic film, insulating substances or glue.

Kind regards

Hey Trevor

I have not received any emails from you, write to me at “postmaster (at) kaizerpowerelectronics.dk” replace with a proper @ for a correct email address.

Kind regards

Hi ramesh

Two capacitors in parallel will double the capacitance and keep the same voltage rating.

Two capacitors in series will double the voltage rating but capacitance will be half.

Try to play around with the capacitor calculator I made for exactly that: http://kaizerpowerelectronics.dk/calculators/mmc-calculator/

Kind regards

69. mamata says:

very very thank you so what if i use two diff capacitor like 2A182J+2A222J+2A332= 732J AM I RIGHT ?

70. mamata says:

but wha if i add 2 cap in parallel with diff volt like 2A232J+3B472=?

Hi manata

When you add different capacitors in parallel, you can just add the capacitances together as you did. But be aware that current sharing will not be equal.

With different voltage ratings, you will have to derate the total capacitor bank to the lowest voltage.

Kind regards

72. mamata says:

ok thank you once again ,
i am so sorry if i am disturbing you agian but i hav one more question for u
when i went to buy 1250volt 472J film capacitor they showed thre type one with green coat another brown one n next blue but the blue one is not rectangle as green n brown but blue one is round n loks completely diff are they all same can they replace each other i need that in compact fluo-ballast where they put to connect to terminal from the tube as starter can i put that blue one

73. mamata says:

actually i thought that blue one is tantalum cap .. is tantalum cap is in blue or it comes in diff color

Hey mamata

Tantalum capacitors can come in all colours, what you have to be aware about is that tantalum capacitors are polarized just like electrolytic capacitors and they will certainly not work in your CFL driver. They are generally low voltage rated and marked with + signs for positive lead.

Here are some examples of tantalum capacitors: http://www.tedss.com/Stock/learnMore/dipped-tantalum-capacitor.jpg

Kind regards

75. mamata says:

ok thank you very much for ur help n i hav last question for u in radial style film cap what does 01M means in capacitor El-Gi-AT KT11 -01M 1KV
2nd question is u know there is a capacitor used in compact fluo ballast at the end out put connecting 2 terminals of the tube what is the function of that cap n what is it called eg.shunt? or snubber ? orHIGH DVDT/PULSE?

what is the general frequency in cfl ?are they same in all powers like 20W 30W 40W?and as current varies ,do voltage varies too according to the power

and do u hav any formula to calculate capacitor for given voltage current n frequency?

I am guessing they are running at a fixed frequency with a simple oscillator and current output is determined by the pulse width of the driving signal. So only a few components needs to be changed between the different power versions.

To find a formula for a given CFL circuit, you will have to reverse engineer it and do it yourself.

Kind regards

79. lo-fi says:

Hi,

I found your website while looking for an answer to a question that I’m not having much luck with.

I’m almost finished replacing some of the caps (and most other components) on some audio compressors and have a requirement for 22pf in the VCA circuit, the only ones I could find were 22pf 500v 5% silver mica’s on ebay which I bought and have now turned up. Will I have any problems using these in the circuit even though the voltage rating is much higher than the circuit calls for? (the unit uses a 9v ac input.)

I’m told that as long as the voltage is higher on a capacitor it should be OK, but this is probably much higher, not that I can tell what the original ones were rated at.

Hey lo-fi

There is no problems in using capacitors with a higher voltage rating, some other characteristics but just the capacitance can however make a difference in the sound in such audio equipment as you repair. dv/dt rating, esr, esl etc, not that I think you will notice a difference.

Only problem with higher voltage rating is that the capacitors are physically larger.

Kind regards

81. lo-fi says:

Hi, thanks heaps for taking the time to respond. appreciate it.

82. mamata says:

i box film capacitor has value of 01M ,is that mean .o1uf?

Hey mamata

Is there a dot or a . in front of 01M, else it does seem that it could be a 0.01uF capacitor.

Which physical size and voltage rating does it have?

Kind regards

84. mamata says:

Hi, thanks for taking the time to respond once again,
there is not any dot(.) so i am confused too,and the voltage rating is 1200v

Hi mamata

Unless it is a big capacitor, then the 1200v rating tells us that the capacitance can not be 1uF, so 0.01uF or 10nF as it is, sounds very reasonable for a some 20mm capacitor.

Kind regards

86. Nosa says:

Can a capacitor of 68UF 400V be replaced with 33UF or 120UF with the same voltage rating?

Hey Nosa

You can replace with the 120uF, without much change in inrush current and with better smoothing capablitiy on your DC voltage. You risk that your voltage will sag with a capacitor that is almost half of the original, so avoid the 33uF.

Kind regards

88. Barry says:

This is a great page…. I need to ID 2 caps one marked 180nj & the other 100nk, both 100vdc. They go in some sort of industrial video display control.

Hey Barry

180nj could be a 180 nF 5% tolerance and 100nk could be a 100 nF 10% tolerance.

Kind regards

90. Barry says:

91. Mr N D Saifi says:

R1
220E
UD
Any idea what I should replace it with?

Hey Saifi

Could you please upload a picture of it or find a similar online? Those numbers does not give me a certain clue.

Kind regards

93. retard says:

1K2
390
2,5V

Hi retard

It is a 390uF 2,5V electrolytic smd capacitor.

Kind regards

95. retard says:

Thanks

96. sam says:

do you have an idea what this capacitor could be?

It’s about 5 Millimeters tall and has its origin in a heating control from an u.s. manufacturer.

Thank you!

Hey Sam

I think it is a varistor and not a capacitor, LF9 and PZ56 are both markings of this type varistor, http://www.datasheetarchive.com/dl/Datasheets-EC1/DSAQ00181551.pdf

I think it is the component on the first line on page 3.

Kind regards

98. sam says:

Oh, great!

Thanks a million!!

99. Newbee says:

Would you be kind to identify the component with black rectangle on it. It has 470nk400 written on it.

Regards.

Hi Newbee

It is a MKT, metallized polyester foil type capacitor with a capacity of 470 nF, 10% tolerance and 400 VDC rating.

Kind regards

101. Dan says:

I think MPP is Metallized Polypropylene too.

102. Francisco Cardona says:

which is the equivalent of the tantalum capacitor is to be 10 microfarad , what is your voltage ?

Hello Francisco Cardona

The 2nd line on the capacitor shows it is a 50VDC rating, the K with lines above and below is a ID tag related to the manufacturer.

Kind regards

104. mahlatse masanabo says:

Hy
I am looking for a 33pf capacitor and I cnt seem to find it anywhere in my components and its polarized. Can you please kindly send me a picture of that. And I have like 104 capacitors which is like 100nF but here they used gold but I have blue. Is it find if I use the blue one?

105. eileen brennan says:

i have been to 2 electric component stores and no one seems to be able to identify these capacitors. the first ones markings are 473 J and an S with a circle around the S and then underneath that 630 and what I think is an asterisk and a P . the second capacitor is slightly smaller reads 223 J and as S with a circle, underneath it reads 630 asterisk P.they are both out of a sony trinitron tv brown in color a little less than an inch in length rectangular in shape. Any help would be so greatly appreciated, it’s my mother’s tv and she doesn’t want to part with it. Thank you

Hi eileen brennan

I think you are talking about this type of Metallized Polypropylene Film Capacitor. 473j 630 is a 47 nF 5% tolerance capacitor rated at 630V. 223J 630 is a 22 nF 5% tolerance capacitor rated at 630V.

Kind regards

107. eileen brennan says:

Thank you so very much for your quick and informative reply. I have already ordered them online, thanks to you. It is sometimes easy to get discouraged when trying to learn something new but this website has explained a great deal to me in any easy to understand way and for that I thank you also! Things I would often throw out when they stopped working have been brought back to life with a little elbow grease and researching on the web. Just wanted to say thanks again.

108. NOOB says:

Hi

Could you help me identifying these 3 capacitators?

I think the second one is 120uF 50V, but not sure.
Can you tell what parametres these 3 components have?
Or where can I find it out.

Hey Noob

The first is a 1.8 uF 410V electrolytic capacitor, black mark is the negative terminal.
The second is a 120 uF 50V electrolytic capacitor, black mark is the negative terminal.
The third is a 1 uF 400V electrolytic capacitor, black mark is the negative terminal.

Kind regards

110. mamata says:

i hav few capacitors from CFL which is connected parallel to the polyster capacitor 2n2K,AND VALUE WRITTIN AS HL PR1 in one and SP MZ6 in another ,, the capacitors as i think ..both are round in shape and light green coloreed and surface is rough not smooth like that of other none electrolite caps can u give me some info

111. mamata says:

after while i got the pic from net as the Thermistor so plz tell me what is it what are the fxns and its role in CFL and the values like HL PR1 , SP MZ6( these are found in 20W CFL bout in one CFL its HL PR1 and another has SP MZ6 so i am confused abt its value
waiting ur reply ..thank u for ur kind info

Hey Mamata

A PTC thermistor is used for current limiting or temperature limiting. As the SP MZ6 heats up, its resistance rises and thus no significant current can flow in the circuit.

It is used as a protection against run-away CFL circuits.

Kind regards

113. mamata says:

thank you but i couldnt find any site about guide of the lables on Thermistor can u give me some idea on that

114. Jayde says:

Hi Mads, i stumbled onto your site and i hope you can help me. I have two blown Metallized Polypropylene Film Capacitors (At least i think they are) with markings on that says 250v~×2 0.47uf +- 10℅ the code is mev473. The board comes out of an old aim microwave situated directly after the main power inlet. Can i replace these capacitors with anything else? I dont have access to parts now, but would like to know the posible alternatives when i do. Thank you in advance. Jay-De strydom.

Hi Jayde

You need some MKP Y1 or Y2 capacitors to replace those, as they are line to earth capacitors in your input filter.

Kind regards

116. Jay-De says:

Thanx a million for the info, i really appreciate it!

Kind regards
Jay-De Strydom

117. Lexo Foyde says:

Hi mate
Could you please help me with a capacitor, its used in a cars airbag circuit. The capacitor reads “470nJ63” its a EVOX cmk, approximately 10mm squared 5mm width, yellow in colour. Done some research, could be polycarbonate, not sure. Any help would very appreciated, thank you

Hey Lexo Foyde

Just from the text on it it is quite clear that it is a 0.47 uF and 63 Volt capacitor, you can replace it with a PP/MKP/FKP (polypropylene) capacitor, you do not have to find a polycarbonate.

Kind regards

119. Lexo Foyde says:

Thankyou very much, helped me heaps, cheers

120. Bar says:

Hi, sorry to be another person with zero knowledge, having a hard time finding a replacement polyester(?) capacitor from a TV.

Has on it –

105 k 500
P472 MPP
3356554

From what I’ve read it may be a .47uf with a metalliszed polypropylene film, guessing the last digits are a part# but what’s 105k and 500?
Thank you for any information you may able to share.

Bar

Hey Bar

I would think that the first line give us the capacitance, tolerance and voltage rating. So I would guess this is a metallized polypropylene 1 uF capacitor with a tolerance of 10% (K) and 500 Volt rating.

Kind regards

122. Bar says:

Thank you for your response, I’m way out of my element.

123. daniel says:

i have a surface mounted transistor coded cy334 used on a Samsung premium hi-fi audio system.i cant find one like it and i cant find the equivalent.can you help sir

Hey Daniel

CY334 is likely just the location number on the circuit board, you have to look at the text written on the component.

Kind regards

125. jamrock says:

what value capacitor can i use instead of two 47pf 1kv capacitors in parallel.

Hey Jamrock

Paralleling capacitors double the capacitance, it corresponds to a 98pF 1kV capacitor, a 0,1nF would properly be fine too. They could however be in parallel for a higher current rating, you have to take that into account too.

Kind regards

127. Kostas says:

I want to replace the tantalum capacitor shown in the picture attached and I’m looking for an equivalent one. If I’m not mistaken, the capacity is 4,7μF and the voltage is 50 Vdc. What I haven’t figured out is the 3rd line of marking. What does the number 315 mean? Is it crucial for the capacitor’s performance? Thanks.

Hey Kostas

You are right about 475 being 4,7 uF rated at 50VDC.

+315 tells us that the leg in this side is the positive terminal and 315 is the print week code, shorted PWC and is written like this YWW (Year 1-digit/Week 2-digits), so 315 is week 15 in 2003.

Kind regards

129. Kostas says:

Thank you for your prompt response.
Kind Regards,
Kostas

130. Curtis Mount says:

I need a cd263 capacitor for a welding machine. I would like a price an how long to receive it.thank you very much.

131. Noob says:

Hi
Its Noob again. This time I have a difficult one.

Marking on it is:
HD604J
H3K2192H

Hey noob

It is a 0.6 uF film capacitor with 5% tolerance, guessing from the physical size and capacitance it is properly not rated for more than 50VDC.

Kind regards

133. Francisco genao says:

Good afternoon,

Im trying to find out what is this . I have a backplane that have like 50 of this i dont capacitors or filter . I would like to know what is this and where i can buy it on line?

Thank you very much,

Francisco

Hello Francisco genao

I think it is a 10 uF tantalum dual capacitor.

Kind regards

135. Tim says:

Here is a great cheap little tester on e bay it will test any components you can think of

136. Tim says:

here is a close up

Hey Tim

Thank you for the recommendation, the one I had is defective so I could use a new 🙂

Kind regards

138. Steve says:

Hi Mads, this is out of a windshield wiper motor from my vehicle.Is this a tantalum +/- 10% capacitor?

139. Donald Husar says:

I have two capacitors I removed from a 1935 Rickenbacker amp. I need help finding a replacement part for them. Can I get help with new part # and a vendor to purchase from?

Little Americans Dry electrolytic Cap. 8.8 @ 450V

No Vendor on second part. Numbers are 20500 SCR 6647-18

Any help is appreciated.

Don

Hey Steve

I think it is a ceramic capacitor, I got no idea about the value of it. When current passes through one of the coils it is the slow setting and when it passes through capacitor and coil in series it is the fast wiper setting. So there is properly some timing change with different capacitances.

Kind regards

Hey Donald

In old amplifiers they used capacitor that was generally too small to smooth the high voltage properly, since they were expensive or just not invented yet.

Replace the first with a 22 uF / 500VDC capacitor, f.ex. this http://www.digikey.com/product-detail/en/UCY2H220MHD3/493-6960-ND/3664330

You could also go higher up in capacitance, but properly not more than 50 uF, you would risk to blow up the rectifiers.

I got no idea about the second, maybe some pictures would help.

Kind regards

142. Donald Husar says:

Mads, Thanks for the info. I’ll send pics of the other part tonight. Question: is this the best part to install? I am looking for optimun performance out of the amp.

Don

143. Steve says:

Mads,your guess is as good as mine it came out of the LanRover it was assembled in Hungry. I tried to look up European symbols on capacitors and had no luck thanks though.Steve

Hey Donald

I do not believe in “audio” grade capacitors, I build my stuff with regular parts and do not spend thousand of dollars for special good sounding capacitors that need to burn in for 500 hours first, in my world that is just bullshit.

Careful engineering and measurements will guide you to the optimum performance.

Kind regards

145. Donald Husar says:

Here is a pic of the other part I need for my Rickenbacker amp.

Hi Donald Husar

That looks like an old oil and paper capacitor and a quick guess would be its 2 uF and 500 VDC, I would however like to know where in the circuit it is used to be sure about the rating.

Kind regards

147. sam says:

Hi, I’m working on something that needs replacement but im having difficult time finding the exact component. what can you recommend as replacement to 223J2KV capacitor?

Hey Sam

You should replace it with a metallized polypropylene capacitor with a capacity of 0.022 uF and rated for a voltage of 2kV.

Kind regards

149. Pedro R Morales says:

I have a defective microwave oven’s high voltage capacitor rated as 2100vac, 0.70uF. Can I replace it with one with the same voltage rating but 1.05uF capacitance? Do you think this increase in capacitance could be dangerous in terms of shifting a little too much the design specs of the microwave oven?

The defective cap got shorted out, I think maybe a higher capacitance will make it easier for the cap to handle the power requirements of the magnetron. I have tried to get the right cap in terms of capacitance but it has been impossible.

prm

Hey Pedro

The capacitor is only used for a voltage doubler, so there is no difference in operation of the microwave oven with a 1.05 uF compared to a 0.9 uF.

The resonant frequency of the microwaves are determined by the magnetron cavity and construction.

Kind regards

151. Pedro R Morales says:

your answer releases me of my worries about altering the design too far and, at the same time, I was expecting it since more capacitance implies more current capability due to larger cap plates. The previous cap, as I wrote you, got shorted out, so I expect the 1.05uF cap I have to make a better job.

Thanks a lot, really appreciated!!!

prm

152. Harry says:

Hi

I’m trying to find a replacement capacitor.I’ve found some that has all the same writing on, 0.047uf 160 but at the bottom it says wima fky instead of fkc. I think my amplifier was made early in the 60’s so very hard to find out anything apart from that it’s a film and foil construction. Any help would be greatly appreciated. Thanks I can’t upload a photo even though it’s under 2mb?

Hey Harry

WIMA wrote a guide about substituting obsolete Polycarbonate capacitors: http://www.wima.com/EN/polycarbonate.htm

Kind regards

154. eds says:

I have capacitor which is 3,15 uf in a value. i don’t have an idea what is the value for it. can you please help me for the exact value?

Thanks,
Eds

Hey Eds

Could you upload a picture of the capacitor? I am not completely sure what you are asking about, voltage rating? You already know the capacitance is 3,15 uF.

Kind regards

156. Seth says:

I have a capacitor out of subwoofer marked:
.039J
100HT
What does that mean? Is it a .039u capacitor with a 5% tolerance?

Hi Seth

I would also say that it is a 0.039 uF 5% tolerance with a voltage rating of 100VDC. To be sure I would like to see a picture of it 🙂

Kind regards

158. Seth says:

Thanks so much. Here is a picture of the little bugger.

Hi Seth

From the size of it, there is no doubt, it is a 0.039 uF / 39 nF if you like. 100 Volt rating.

Kind regards

160. Bigbizkit says:

Hi guys, im a little confused…
So, i have these two caps, Mylar and Ceramic, they both have a marking of 104,
Are their values the same?
Thanks!

Hey Bigbizkit

Yes, they are both 100 nF capacitors, just made from different materials.

Kind regards

162. Amit Dua says:

Dear Sir,

Please let me know how will we calculate the exact value of film capacitor of SMPS led drivers.
I am designing led driver with sharp IC need to know how will calculate the film capacitor value for high accuracy in my drivers.

Thanks
Amit Dua

Hi Amit Dua

I can only advice you to read how to design the circuit around the IC from the datasheet. You give me too little information to give any real advice.

Kind regards

164. ANISH says:

DEAR SIR,

CAPACITOR CODE IS 1UK 63, WHAT IS THE VALUE OF THIS CAPACITOR.

THANK YOU

REGARDS,
ANISH

Hi Anish

It is most likely a 1 uF / 63V capacitor.

Kind regards

166. Sharif says:

Can you help me understand this code? this is a 2002 Pontiac control unit and it not working because of that capacitor with code 4.19G

Hi Sharif

I am not completely sure what it is, but from what I can find it might be a 4.19 MHz crystal, try to see how it is connected to the IC close by and find the datasheet for that IC to see what the purpose of the component are.

Kind regards

168. Ric says:

Hi there. A lamp of mine stopped working and I narrowed it down to this capacitor where power goes in, but does not come out. Can you help me identify it so I can buy a replacement? Thank you!

Hi Ric

It is a 47 nF 250VAC MKT capacitor. If you replace it you should use one with a higher voltage rating, since the old one failed it does not hurt to upgrade the design a bit.

A capacitor does not quite work as power goes in and out of the other end, are you sure this component is even at fault? How did you measure / determine that it was bad?

Kind regards

170. Ric says:

Hi Mads. Thanks for that info. I used a multi-meter with the power connected and the dimmable lamp switch all the way up, to check all components. No power goes past this capacitor. (please see attached image) I found these on eBay. Will they work? I know you said to get one with a higher voltage rating, but I already purchased them. I can purchase more if you really think it will help. Thanks again!

Hi Ric

A regular multimeter is only made for measuring frequencies to up around 1 kHz or even as low as 400 Hz. A light bulb operates at a high frequency into maybe 100’s of kHz and you are not able to get a reading at these frequencies with your multimeter that are useful for fault finding on a switch mode power supply circuit.

Kind regards

172. George says:

Hello,
What is the difference between CBB22 630V 0.1uF and CBB22 400V 0.47uF Metallized Polypropylene Film Capacitors. Can I use a CBB22 630V 0.1uF instead of CBB22 400V 0.47uF, because the other is not available. It is for the replacement of a damaged LED flood light circuit capacitor.

Hi George

You can always use a capacitor with a higher voltage rating, but not always one with a lower voltage rating, as the capacitors breaks down from excessive voltage.

It depends on the role of the capacitor in the circuit if it is possible to use another capacitance. From what I can find from LED circuits, it should have a value around 0.33 uF to 0.47 uF, as it forms a part of the current limiting network to protect the LEDs, so I suggest you find a higher value than 0.1uF.

Kind regards

174. George says:

175. Kevin Gibson says:

Greetings Mr. Barnkob,
I am replacing a compromised capacitor on my computer motherboard. I have included a photo of another identical one that is on the same motherboard. My question is about the value of the capacitor. From my understanding I interpret the value codes as being 16 volts and 270 picofarads (pF). My local expert tells me that it is 270 microfarads (uF).
Thank you very much for your time.

176. Kevin Gibson says:

Hi Again,
I forgot to mention that the physical dimensions of the capacitor are 8mm diameter and 12mm long.
Thanks

Hi Kevin Gibson

I think you local expert is right.

The blue mark shows that this is a polarized capacitor and most likely a electrolytic one.

With a 16 V rating 270 uF sounds reasonable for the size of it. What the manufacturer did was reset the normal capacitance rating code to start at 1 uF. so 270 would be 27 uF and in your case 271 is 270 uF.

Kind regards

178. Kevin Gibson says:

Thank you very much kind sir.
Only good fortune to you for your assistance.

179. Jeffry says:

Hi Mr Barnkob,

Can you please help me idetify the voltage value of these caps and where can i find reference to identify them

Hi Jeffry

SMD components can be a real pain to identify alone from the markings, as they often invent their own new scales using old codes. You need to either measure them or see where in the circuit they are located and if the value on them would make sense in regard to the old capacitor codes.

It seems to me that manufacturers no longer publish schematics and now even fewer components have full markings, it might be a steps towards ending the new wave of home repairs of electronics.

Kind regards

181. Jeffry says:

Hi Mr Barnkob,

Thank you so much for the suggestion

182. Cartel says:

Kudos to Mads for his quick answers to the worlds questions on capacitors.

Good job!

Thank you very much Cartel 🙂

184. Nick says:

HI There nice helpful post… Can anyone confirm what this is?
I am thinking / hoping a 39 pF Tantalum Capacitor but definitely not sure… It is off the logic board of a Mac Mini where all capacitors seems to be rated at 16V.

Hi Nick

If you are sure its tantalum, I doubt very much it is 39 pF, that capacitor technology is not for small capacitances. What I have seen on SMD markings is that they tend to be in uF, so this is properly a 39 uF / 16 V capacitor, also judged from the large size of it.

Kind regards

186. Nick says:

legend – thanks a lot for the reply… Yeah I guess you are right about the size of it so probably 39 uF… I am not sure that it’s tantalum – I just thought that these were the only ones in this shape and style… It seems very light and not metallic… So any way to check / know if it’s tantulum? Cheers again for chiming in 😉

187. Enrique Reyes says:

188. Younus says:

I have a capacitor which is marked as: D473K2A

189. Younus says:

I have a capacitor which is marked as: D473K2A

what is the capacitance of this capacitor.
Do these codes hold good in ASIA as well or not?

Hi Younus

473 is 0.047 uF

Kind regards

191. NAREN KUMAR K says:

Hi. My soundbar couldn’t be switched on. In many forums it was said to replace the capacitor. It reads 223j 400v. But I could not find similar capacitor here. What I get here is 224K 400v and .0022/k 630V. Which one to try

Hi Naren Kumar

Where in the circuit is this capacitor? Try with the 224K 400V first.

Kind regards

193. Simon says:

What a fantastic resource. Thanks; -)

Hi Simon

You are most welcome 🙂

Kind regards

195. David Lania says:

I’m having trouble with finding out what the marking 68K on a capacitor means. If you could tell me that would be so awesome. A photo is attached
.

Hi David

Your picture is missing, but a first guess would be that it is a 68 pF with 10% tolerance. I would be able to tell more precise from seeing its physical dimensions.

Kind regards

197. Melvin Nazario says:

just want to ask if is there a replacement for a 225k-250v film coated capacitor, but not a film coated capacitor? and or does a running capacitor can be use as a replacement. thank you in advance.

198. Noob says:

Hi
Its Noob again. Could you help me out again? Small orange capacitator!
Is it possible to figure out size too?

Hi Melvin Nazario

You should replace a 225K/250V, which is a 2.2 uF capacitor, with the same type. Use a MKP or MKT capacitor, is it by any chance a X1, X2, Y1 or Y2 marked capacitor in a input filter?

Kind regards

Hi noob

SMD components are always a little tricky. This does however seem to be a 2.2 uF tantalum capacitor.

Kind regards

201. Jamie says:

I have a schematic that calls for 3 capacitors but I’m not sure what it’s saying.
100M/25V electrolytic capacitor ?
.01M 50V disc capacitor ?
.47M/25V electrolytic capacitor ?

Any ideas? This is all the information I have.

Hi Jamie

The notation seems to be capacitance, tolerance and voltage rating.

The only capacitance range that makes sense would be uF, due to the first 100M would be a extremely large capacitor if it was 100 mF and a ceramic disc of 10 uF (0.01mF) is unusual.

100 uF / 25 VDC electrolytic capacitor
10 nF / 50 V ceramic capacitor
0.47 uF / 25 VDC electrolytic capacitor

Kind regards

203. Jamie says:

Thanks!

Good value calculated method

205. Jason says:

I have an InFocus projector where the light stopped working (it is out of warranty)

After I opened the unit I see that 1 of the 3 Box type double sided metallized polypropylene film capacitor’s was broken and not making a connection.. I could not get it to solder on to the small stud left on the bottom.. so I need a replacement

Pictures show the info.. This is on the circuit board that the light plugs into..
This is what I think it is etc..
GD (Brand) MMKP84
Box type double sided metallized polypropylene film capacitor
222J700
222=Capacitance (22×100 =2200pF & =2.2nF & =0.0022uF)
J=Capacitance Tolerance (+-5%)
700=Rated Voltage

Any help where I can get 1 of these??
Jason

Hi Jason

Ebay is properly your best bet. Just find a 2.2 nF MKP capacitor with a voltage rating higher than 700 VDC, like this: http://www.ebay.co.uk/itm/5-x-2-2nF-0-000uF-0-000-F-1600V-MKP-10-RM15-Folien-Kondensator-Cap-WIMA-5pcs-/151426407843?hash=item2341b79da3:g:y3YAAOSwFqJWsI4z

Kind regards

207. Jason says:

I think this is the actual spec sheet etc for this item:
http://e-neon.ru/user_img/catalog_datasheets/mmkp84%20specification.pdf

I wish I could find the exact one somewhere…

I call the Manufacture of the projector (InFocus) they told me that their authorized repair company might be able to sell me the part (the are Mendtronix) but when I called them they told me that InFocus does not allow them to sell their proprietary pats!

I searched on E-bay like you suggested, but I am not sure on the Voltage, as these specs say 700V AC, also on the actual size dimensions..

The one you suggested do you think it matches the spec sheet close enough?? +-5% compared to +-10%? plus it is 1600VDC not AC??

Again, any suggestions anyone has, or if anyone knows where to get this exact item I would be indebted to you…

Thanks

Jason

Hi Jason

700 VAC means that +700 going to -700, as it is alternating current. A MKP capacitor of a DC voltage rating above that span is just as good, just add some more voltage overhead, maybe get a 2000 VDC rated or even higher.

Almost all MKP film capacitors are with the same performance to equal sizes, do not worry too much about getting a original, that just sounds expensive 🙂

From the pictures you can see that it is 3 capacitors sitting in series from the transformer to the output of the 2 grey wires, so it is basically a 3×700 AC rated and 2.2nF/3 capacitor bank. So I would not worry about 5% or 10%. If you do, just buy 10 and match them with LCR meter.

Kind regards

209. Ravs says:

I have a capacitor with 1K2 marking on it? Would you know its value? Any help is appreciated.

Thank you!

Hi Ravs

It does have the form of a silver mica capacitor, but not any of the old marking codes from those times.

Maybe it it a inductor or some coupled component like LR or LC. You will have to solder this one out and measure it to be sure.

Kind regards

211. Joe says:

Hi,

Trying to find if this is a ceramic capacitor, photo is taken from the inside of the controls cabinet of a 1960’s machine tool known as a horizontal boring machine. We had a problem where the a mains cable to the DC Motor wore through the sheaving and arced up. The machine does still work but the DC motor wont turn on however the motor is fine, just looks like the signal from the stop/start button isn’t telling the contactor to pull in or out. The only thing we can see blown are these things in the photo so that’s what the best place to start. We don’t know what they are except look like ceramic capacitors and a Google search has lead me here.

Can anybody help us????

Many thanks.

212. Hendrik Nentjes says:

Hi there!

Could you help me with the following caps?
I can’t figure out how to get the right values with your tables..
They come from an amplifier and are 6,5 and 8 mm in diameter.

Hi Joe

I do not think those are capacitors. They might be old disc style power resistors. 150 Ohm at 4 Watt, try to desolder one of the good and see if it measures 150 Ohm with a multimeter.

Kind regards

Hi Hendrik Nentjes

These are SMD electrolytic capacitors. Both are 47 uF in capacitance. The small one is rated at 6 VDC and the large one 35 VDC.

Kind regards

215. Steve Teodecki says:

I’m trying to understand what voltage this radial type capacitor is. The top row reads 8019P and the second row reads 100L.
I’m guessing it’s a 10pf capacitance based on the 100. Is L a rating between K=10% and M=20%? My real question is the voltage. There is no 1K or other code before the capacitance code. What does the 8019P mean?

Hi Steve Teodecki

I would need to see a picture of it. I do however doubt that a capacitor that fits so much writing would only be a 10 pF, as that is really small. The numbers does however not ring a bell.

Kind regards

217. Wypl says:

Ola poderia me tirar uma duvida
2u2k seria igual a 225j ??

218. Szop Gracz says:

Could anybody please tell me What is the voltage rating of this thing?

219. Szop Gracz says:

Alright after inspecting the circuit I’m guessing it’s 630V.

220. Szop Gracz says:

Well I just measured the voltage with more accurate equipment and it was over 1kV on this component so my previous guess I must be wrong. Is this even a capacitor?

Hi Szop

I would guess that it is a capacitor, 15 nF and 630 V, now the question remains is it rated for AC or DC voltage, if it is 630 VAC, 1 kVDC is not impossible. But what about your measuring meter? Are you measuring peak AC, RMS AC or DC?

Kind regards

222. Andrew says:

I Have an old NV1 Diamond Edge 3D Graphics card from 1995 and its got some blown Caps.
5n
10
16v
I’m not exactly sure what the 5N and the 10 would stand for, my guess is that 10 is the uf?

Hi Andrew

If it is a electrolytic capacitor, aluminium can with black markings/text. Then I think you are right, that it is a 10 uF / 16 V capacitor. I attached a similar to what I think you mean.

Kind regards

224. Randy says:

Hello -I am trying to verify all info on this cap to locate a replacement. It is used in a 110VAC motor starting application and is in parallel with the stop button. It is starting a small induction motor directly. The motor also has a cap in parallel with the motor. This was installed on a group of industrial machines that were built around 1979.

My guess is that it is a .01 uF with +/- 20% tolerance. My thoughts are its rated at 1000VDC (but I do not fully understand why DC rating is used in an AC circuit). The E marking I am unsure about.

What would be the 2 inside the circle at the top? Is that a manufacture logo?

Hi Randy

Did you forget to upload the picture?

It could sound like you have a start capacitor and a run capacitor.

Roughly you can say that DC rated capacitors, if they are film or foil types, can be used in AC circuits if the peak to peak AC voltage is within the DC rating. Datasheets normally state a AC rating for DC rated capacitors.

Kind regards

226. Randy says:

Sorry about that. Here’s the pic.

Hi Randy

That is a ceramic disc capacitor, rated 1 kV / 10 nF.

The circled 2 is properly a manufacturer logo.

Kind regards

228. Randy says:

Thank you so much! Greatly appreciated.

Randy

229. Ema says:

Hi i m in search of what kind of cap is this. Seems a ceramic disc but then no clue about voltage and Farads. Can you help me eith it? It is btw the output leads of a ac/dc transformer in parallel with a small bulb. The board belongs to a Bose 901 IV series equalizer. Thanks in advance

Hi Ema

Kind regards

231. Prakash Chand says:

Hi, we are manufacturer of LED lamp of 3 to 7w 220vac. In this process we use a capacitor CBB22, 125J 400V. But this capacitor get blast on 220vac supply.
Please suggest me, how can resolve this fault. If need to change capacitor,how mu h rating will be suitable.

Hi Prakash

I do not do electronic design for free for manufacturers, it sounds like there is something seriously wrong in your circuit or design for this to happen.

Kind regards

233. mot says:

hi mads is it possible to replace my faulty 225j 400v capacitor with a 474j 400v?

Hi mot

It depends what application the capacitor is used in. You have a 2.2 uF capacitor there now and wants to replace it with a 0.47 uF capacitor, with only 25% of the original capacitance this could affect how your circuit works.

Kind regards

235. mot says:

I am currently working on my rechargeable LED lamp. The unit is not charging and i found out that one of its capacitors(CBB22 225J 400V) blown out. However, i cannot find same capacitor in the market. The only available replacement is 474J 400V, will it work?

Hi mot

Is it a part of the mains input filtering circuit? It will properly work with 474J, but noise filtering might be less than its original design.

Kind regards

237. mot says:

Thank’s mads for your help.! The replacement capacitor seems fine and the unit is finally working. Greatly appreciated.

238. Omkumar a v says:

2J102j capociter remove and 2j472j capociter fixed . This is normal r equal value ?
please give me best ideas. Thank u.
A V OMKUMAR

Hi Omkumar

You replaced a 1 nF capacitor with a 4.7 nF capacitor, depending on the type of circuit this could have disrupted timing circuits. If it was just some kind of decoupling in a power supply rail, it will work just fine.

Kind regards

240. Nick says:

I have a capacitor out of an automotive Ignition Module that’s failed… I’m looking for it to repair the module. It’s numbered as follows.. 103J630/N1SV41.. first number above the second… no color stripes.. it’s orange coated… symbols on the board is of a fixed cap.

Hi Nick

Sounds like a metallized film capacitor, you can find these in many place. 103 is a 10 nF and 630 is 630 VDC rating. http://www.ebay.co.uk/itm/20PCS-CBB-103J-630V-0-01uF-10nF-P-10MM-Metallized-Film-Capacitor-/272194319970?hash=item3f600bb662:g:UzAAAOSwGYVW~QFE

Kind regards

242. najib says:

Hi everybody.
Need help. Someone could explain this code CTU272K printed on capacitor.
(I guess 272k means 2700pf tolerance 10%) but CTU ?
thanks

Hi najib

I think that CTU is just the model number of the manufacturer. There seems to be some Russian made capacitors that uses this model-numbering with CTU in front.

Kind regards

244. sabil says:

Can anybody tell me the equivalent capacitor of 4.7nf 250v?
please do the needful at the earliest.

thanking you.

Hi sabil

That would still be 4.7 nF and 250V rating, you can get these values in different types of capacitors, depending on which application you need to use it in.

Kind regards

246. dire_wolf says:

What does 18L stand for in a 18L/683 (0.068) metal film capacitor and what is A1 in a 271/A1J (270 pF) ceramic capacitor?

247. Gbenga olawuyi says:

I FIND IT DIFFICULT TO GET 22nf 600v capacitor in my local market ,what is the replacement pleases .I need help

Hi Gbenga

You can use any capacitor, of same type material, that is 22 nF but with a voltage rating of 600 V or higher, that might make it easier for you to find one, maybe rated for 1000 or 2000 V.

Kind regards

249. Vamsi says:

I want difference between 225k,400v and 225j,400v

Hi Vamsi

K is 10% capacitance tolerance and J is is 5% tolerance. The J rated capacitor is guaranteed to be closer to the given capacitance value.

Kind regards

251. Noob says:

Back in ”June 22, 2015 at 01:14” post, you helped me out with one capacitator.
Finally I found some time to replace the part, but and used a WIMA 0.68uF 63V cap, to replace the old one. The new one blew up instantly. Then I replaced with WIMA 0.68uF 275V, and the unit turned on perfectly.
But the problem is tricky. Original capacitators size was 15 x 15 x 5mm. And there is no place to instal a bigger capacitator.
The thing is that I cant find any 0.68uF 275V capacitator to fit the place.
All are bigger.
Should I use capacitator with smaller capacitance?(those should be smaller in size)

Or maybe just keep on looking, till I find what I need. (Still a lot manufacturers to browse through)

252. Basem says:

Hi Noob

Could you extend the leads of the capacitor and place it somewhere else in the circuit? It sounds like you tried with one with too low voltage rating, which is why it blew up. Unless the circuit around the capacitor delivers a too high voltage for the original design.

Kind regards

Hi Basem

It is a MKT, metallized polyester foil, type capacitor with a capacitance of 30 nF (5% tolerance, its the letter J) and voltage rating of 250 V.

Kind regards

255. Aries Aguilar says:

Hi. My cApastor label as 47nj 630.. i can’t find a capasitor label as 47nj 630.. what is the best replacement value for my capasitor… thanks

Hi Aries

If the capacitor is a part of a RC timing circuit, you need to find one with the same capacitance, but the voltage rating indicates that this is not the case. You could try to use a 33nF, 47nF or 56nF capacitor instead, with a voltage rating of 630V or higher, maybe you have better luck finding one at 1000V rating.

Kind regards

257. Aries Aguilar says:

Sir mads.. it is connected from ground through the collector of horizontal output transistor of colored TV..

Hi Aries

I would advice you to use a capacitor with a higher voltage rating than the original, but with the same capacitance, else you might risk changing the scanning characteristics of the line output transformer that is supplied by the high voltage transistor.

Kind regards

259. Ben Sturdy says:

Very useful table thank you so much. This was easily the best information I could find on the internet and it has helped me understand how to find the right capacitors for building a synthesiser (so far so good – at least partly working!). The different electronic parts suppliers using NF or UF or PF interchangeably seemed impenetrable. You have made me realise it is easily understandable (usually!).

Wishing you all the best for 2017.

Hi Ben

Thank you and I am glas that I could help you learn and move on the electronics hobby. Do you have anything online to show about your synthesiser?

Kind regards

261. Michael says:

Hello,

I have two capacitors that need to be replaced on a motherboard. I’m new to the realm of capacitors and soldering so I’m not sure how to seek out replacement capacitors.

I’ve attached a pic of the capacitors I’m looking to replace. They have a 5N 10 16v on the top of each. I was wondering if you could point me in the right direction on how to search for a suitable replacement as my search for 5N 10 16v capacitors hasn’t lead me to anything I feel is a match.

Michael

262. Joseph says:

Very use full think you

Hi Michael

Those are SMD electrolytic capacitors, as the soldering pads are quite large, you could solder in a regular through-hole capacitor instead, if you can not source the right ones.

They are 10 uF / 10 V electrolytic capacitors and that is what you should replace them with.

Kind regards

264. Michael says:

Just for my own future reference, could you tell me how I’m supposed to interpret the letters/numbers on these capacitors?

In looking at them saying 5n / 10/ 16v on the capacitor, I’d assume it’d be 10uF / 16 V and not the 10 uF / 10 V you recommended.

Thanks for your time once again.

Hi Michael

You are absolutely right, I did of cause mean to write 16 V. Sorry for that.

To learn how to read the capacitors, you just have to see a lot of them, check out their datasheet from the manufacturer and then at some point you can easily read the different marking systems. One of the problems with SMD components is the lack of a marking standard, but most will always have capacitance and voltage rating + a manufacturer code or series number. Then just rule out what could be what. 5N is not really related to anything, 10 alone as a number is known from film capacitors where you just write the capacitance in uF in a plain number and if a number ends with V, its usually the voltage rating.

Kind regards

266. Freeborn Umukoro says:

I find your post very helpful, I hail you. But my problem is to download it so that I can reference to it at my convenience.

Hi Freeborn Umukoro

Just beneath the article, before the comments begin, the 2nd icon from the left is for printing the article. If you only print the first 3 pages you should have all the essential information on paper or PDF.

Kind regards

268. José Vallejo says:

Can you explain me about this nomenclature for this capacitor CY1K2 332J?. The only I understand that is a capacitor with value 3.3 nF with tolerance 5%, but I do not find explication to the CY1K2. Please, if you can make me free about this doubt. Thank you.

Hi José Vallejo

It is either just a manufacturer name/capacitor product type name etc. The “Y1” could be that it is a capacitor rated for mains to ground decoupling. These are called safety certified capacitors, if you want to find more about this subject.

Kind regards

270. Mauricio Torres says:

Hey I have this capacitor that reads, Z100 on the top line and 224j on the bottom. Now i think ive come to the conclusion that this is a .22uF 5% capacitor but, im not sure of the voltage. Does the Z100 mean 100 volts? What does the Z stand for? Would really appreciate the help!! Attaching photo.

Hi Mauricio Torres

It is most likely a 100 VDC rating, the letter in front can vary from manufacturer to manufacturer. See this picture for different metallized film/polyester capacitor that has a voltage rating of 400 VDC.

http://www.dhresource.com/0x0s/f2-albu-g3-M01-D2-47-rBVaHVZdbyaAekPTAAI8eTEdx14248.jpg/el-env-o-por-mayor-libre-10pcs-cbb-104k-400v.jpg

Kind regards

272. Marco says:

Hi, I think i have a bad capacitor in my humidifier and i think it is this one. It has M 473J NP 200Vs0705 written on it. Can you please tell me how to test if its bad? Also if it is bad what can i replace it with? When i search the internet all i can find is 473J capacitors for guitars and they look slightly smaller and orange in color.(see pic)
Cheers
muks

Hi Marco

You need a digital multimeter than can measure capacitance, if it does not measure 0.047 uF or 47 nF within 5% tolerance (J stands for that) it is most likely broken. You could also use a LCR meter to do a better and more thorough analysis of the capacitor.

You can look for many kinds of metallized film capacitors with a rating of 0.047 uF or 47 nF at 200 V rating, with these search terms you should be able to find one. The smaller orange capacitors are most likely due to newer materials and thinner films, with same breakdown voltage properties as the old ones, but makes them able to make smaller components.

Kind regards

274. Marco says:

Hi Mads, Thanx for the speedy response. I have a digital multimeter but i dont know the setting for checking capacitance, i did try to find the setting on the internet and dont think my meter can measure capacitance(see pic), will try to get my hands on one that can.
From what i gather you are saying that these smaller 473J 200v capacitors being sold as guitar capacitors are the same as the one i need only more compact. Is this one in the pic below a good replacement?(0.047uF @ 200V GUITAR TONE CAPACITOR ORANGE DROP 715P SPRAGUE – SBE)
Cheers

275. Marco says:

Hi, pic of my multimeter.
cheers

276. andrew birchmore says:

Hi I have a TV and this capacitor has blown could you please point me in the right direction for what I need and where I could get 1

277. Marco says:

Hi Mads, It turned out to be a faulty resistor, my humidifier is fixed. Thanx for your help.
cheers

Hi Marco

Good that you found the error. The capacitor you found would make a good replacement, just be vary about cheap capacitors being resold for music/amplifiers often have a much higher price tag than their worth. It is better to buy from real electronics dealers.

Your multimeter can not measure capacitance.

Kind regards

Hi andrew birchmore

You need exactly what it says on the capacitor, a “100nF 275VAC MKP X2” capacitor, the important part here is the X2 rating, it is a safety capacitor that it made specifically for being installed between phase and neutral in a noise input filter. Read more here: http://www.justradios.com/safetytips.html

Kind regards

280. andrew birchmore says:

ok thankyou for your help so with it being a 100nF that would be equivalent to a 0.1uF ?
if so would this do as a replacement:
http://www.maplin.co.uk/p/01uf-275v-x2-rfi-metallised-polypropylene-capacitor-n69cn

thankyou for your help and sorry about the questions iv never delt with this kind of capacitor before and the fact it said nK threw me off

Hi andrew birchmore

Yes, it can also be written as 0.1 uF, you found a perfect replacement there.

Kind regards

282. gsmd2 says:

hi,
it is amazing that this thread is ~3 years old !

I have an LG monitor and it has 4 capacitors
I could not make the symbols at the start, tried several code calculators and read so many references with codes and still cant make it.

especially the one the looks like 6 36MJ 33 100V (probably 100V 33uF but the rest)
Also what is the manufacturer of this, could you explain ?

many thanks 🙂

283. gsmd2 says:

and the photo

Hi gsmd2

The first comments are from 2010, so it is actually more like 7 years 🙂

It is alsmost impossible to tell the manufacturer of these SMD electrolytic capacitors. The only thing you have is the first line which is the production code.

Second line is the value in uF, so here you have 33 uF, 100 uF and 68 uF.

Third line is the voltage rating and tolerance (if there is a letter), so you have 100V, 16V and 35V capacitors and J and K are the tolerance ratings, this could f.ex. be 5% and 10%

Kind regards

285. Anyone who can help me with the size of these 2 capacitors ?

Hi Richard Pedersen

C7 is a 0.01 uF(or 10 nF) / 50Vceramic capacitor. C8 is a timing capacitor sitting together with the crystal at the left, this is a 30 pF ceramic capacitor.

Kind regards

287. BiWeat says:

I have a cap as per picture can you identify it’s 470pF or 47pF? thank you.

Hi BiWeat

I would take that as a 47 pF 10% 400V capacitor.

Kind regards

289. BiWeat says:

Thank you for you help.

290. H says:

If your capacitor is marked 2j472j
Then it means 630v ,4.7nf,5%tolerance

Hi H

I agree with you, 2J472J would be 630VDC, 4.7 nF at 5% tolerance.

Kind regards

292. Pratul Karmokar says:

I have 2 metallized polyester film capacitors with markings
1. CL21 335K 250V
2. CL21 225K 250V
As far as i can make out of it they are both 250V, what do the others stand for?

Thanks
Pratul

Hi Pratul

CL21 is the manufacturers model marking, 225K is 225 for 2.2 uF, as you can read in the table at the top of this page. K is 10% capacitance tolerance. 335 is 3.3 uF. You are correct about the 250V rating.

Kind regards

294. Hi.can i replace 3105j 400v from 105j 400v?

Hi Renan Bandojo Endat

I am not too sure if you wrote something wrong or what kind of capacitor you have in mind. Could you please show a picture of the 3105J capacitor?

Kind regards

296. Michele Mccucent says:

Please how can you explain to me T1,T2 and T3 in the circuit with only two (2) legs or paths and what really is it

Thanks
Michele

297. Michele Mccucent says:

Please can I use 437j 100v in place of 437j 400v???

Hi Michele Mccucent

You can not use a 100VDC rated capacitor when your input voltage is 320VDC, use the 400VDC rated as already meant for the ciruit.

T1, T2 and T3 is each their winding on the same transformer, the dotted line indicates the iron core/ferrite core or the transformer. It seems like T3 is a feedback winding and T1/T2 is the primary/secondary windings. This is my best guess from the limited information about that circuit.

Kind regards

299. Czar says:

Can i replace a capacitor 50v 15000uf to 63volts 15000uf

Hi Czar

Yes, that would be a good replacement, a little higher voltage rating than the failed one you are changing often means that it will last longer as it will be less stressed from operating close to its voltage rating, that is really what kills the most capacitors, too high voltage in a too hot environment.

Kind regards

301. Zack says:

Can i replace 47uf 3kv capacitor with other capacitor?
Any suggestion which uf is equal with 47uf?

Hey Zack

In a high voltage power supply is even more vital to not overload the power supply that this capacitor is a part of, I do not recommend that you exchange it with any other value than 47 uF.

Kind regards

303. Bob says:

I have a power unit for a pool cleaner. The motor was stuck so i freed it up. input to the unit is 110 ac output is 48 dc. Got the motor going off a power supply only up to 40v dc. motor ran at only .6 amps max. Power unit says it is for 2.2 amps. I thought i would jump power unit to motor to see it run at a full 48v. Unit did nothing but flash when whole unit was complete before. As i jumped it the motor was working but smoke started to come out of power unit. what i believe i did was have a strand of wire short across both pins of motor. motor works fine on a power supply. Opened up unit and found a burnt polyester cap with # 333J on top and 630F under it any help what this is? Thanks Bob

Hey Bob

That is a 0.033 uF (or 33 nF) 630V capacitor, if you can see any X1, X2 or Y markings on it, be sure to use a new capacitor with the same ratings.

Kind regards

305. jordan says:

could you please tell me what is the voltage and value of a capacitor with 224k ?
see picture for details.. please explain about the replacement also. which kind of a capacitor could i use instead ?

Hi Jordan

It is a 220 nF polyester capacitor and if it has no voltage rating printed on it, I would assume its 50V, also from the surrounding 35V electrolytic capacitors.

Kind regards

307. Peter says:

hello can you please tell me what the voltage is for these two? I am a bit confused. Why are the dots there?

Hi Peter

I am not sure what the dot means, but they are certainly 250V capacitors.

Kind regards

309. Peter says:

310. ken says:

Ceramic Disk capacitor marked 2C 500v. There are no other markings

Hi Ken

Kind regards

312. Tunde says:

can I replace 224j with 154j

Hi Tunde

That is a 0.15 uF vs a 0.22 uF capacitor, unless it is sitting as a part of a timing circuit, I do not see any problem with a slightly lower capacitance. If it is a filter, the filtering frequencies can change and more noise might be a result.
If it is a safety capacitor like a X1, X2 or Y1, its important to only replace that with another safety rated capacitor.

Kind regards

314. Lukman Efendi says:

Could you help me identify this capacitor. I already go to electronic parts store, but the staff could not identify the value. I already bought the replacement twice, which is not compatible. Perhaps because i bought the wrong values. I already test it with ESR meter but detected as broken. The cap marked is
N25
3KV
SEC

Thank you
Lukman Efendi

Thanks! very useful

Hi Lukman

Which replacement values did you try? How did you know that it did not work? There could be other defects in the circuit that has nothing to do with the capacitor.

I would guess on 0.25 nF / 250 pF, not just from the N used a delimiter, but also its physical size and voltage rating.

Kind regards

317. Lukman Efendi says:

The 1st bought marked 221. Based on your table, that is a 0,22 nF (please correct me if i’m wrong). And the 2nd bought marked 10K and size bigger than the 1st, i assume that would be 10000pF=10nF. For the 10nF, wouldn’t that be lot way to high to replace a 0,25nF. But both replacement size smaller than the real one, aka 0,25nF. And both was choosen by the staff of the circuit parts store. Thank you for your help and reply, Mads. I really really appreciate it.

Best regards
Lukman Efendi

318. Lukman Efendi says:

Well its a small board, i litterally soldered out every parts and test it one by one. It used to power up a scanner’s TL Lamp from a HP printer scanner. It wont turn on, but some times after turn it on and off several times, it can work again. But now it just wont. Strangely when turning off, i can see a quarter part of the lamp is being light up just a glimpse though. Printer service center says they had to replace whole board, since its already discontinued for the support and parts, so they cant repair it and wont take it in. But i already fall in love with this printer, it has many history with me. So i’ll keep it even it will take as many time for me to repair it.

So it seems to be the output capacitor of a small high voltage power supply, the 3 kV rating is vital due to the voltage there, but a rather wide range of low capacitance capacitors should work there, you might even need higher capacitance for it to maintain the high voltage when the lamp is connected as load, it sure sounds like the voltage is not stable enough to keep it lit.

A funny thing is the name of the manufacturer of that little power supply, “Boom power”!

Kind regards

320. Glen Bigelow says:

What is a HL150 12 volt speaker capacitor? What do I buy as a replacement?

Hi Glen Bigelow

Kind regards

322. Michael says:

Am Developing Interest On This Transformerles Power Supply My Quastion Is, This VDC Value Represented By Ie’2J’ Is It The Load Voltage Or? And How Can I Determine The Zenor Diode Code For Voltage Used?

Hi Michael

The voltage rating of a capacitor is the absolute maximum rating, you should always keep a head room for voltage swings, transients and unforeseen events. If you always keep a 20% head room you will also expand the expected life time of your capacitor.

For zener diodes, look in the datasheet from the manufacturer to find the code for the voltage you need.

Kind regards

324. Eric says:

I am trying to replace a .47 MFD capacitor at 250wv, and have found a color coded capacitor, with the color bands being: 1 yellow, 2 violet, 3 yellow, 4 white, and 5 red a little space further apart from the rest. Is this the correct replacement to the .47 MFD at 250 wv, capicator. Thank you Eric mootz

Hi Eric

According to http://www.electronics-tutorials.ws/capacitor/cap_5.html then that is a 0.047 uF capacitor with the colour codes you described.
As it is only old capacitors that use this coding, where on modern capacitors it is written in plain text, I would recommend to find a new and more modern capacitor than such old ones.

For 0.47 uF, the third band had to be green.

Kind regards

326. Bill says:

Side 1- µ1 J100. Side 2- 1UN. Color – blue.
???????

327. bill says:

pics

328. bill says:

pics2

Hi Bill

It is a 100 nF MKP capacitor, with 5% tolerance and voltage rating of 100 VDC.

Kind regards

330. Bill says:

Thank you!

331. RL says:

I have a capacitor marked as ” 1000 µ-M ” 25 Volt. I’m assuming it’s a standard 1000 uf 25 volt electrolytic cap, but it’s bigger than the newer caps of the same value I have here.

Hi RL

You are right, that it is a 1000 uF, 25 VDC capacitor, M is for 20% tolerance.

New capacitors made with newer/better materials are just smaller than what it was just 10 years ago. Especially new materials with a higher dialectic constant helped making them smaller for the same voltage rating.

Kind regards

333. RL says:

334. Jose Vazquez says:

Hola Bill.
Mi duda es de que voltaje es, y por cual puedo sustituirlo.
Te envio una imagen.

Un abrazo.
Pepe

335. Demian says:

Hi guys, I have a surfase mounted capacitor like this.
2N
470
EZA

It’s mounted on the TV power supply board.
Any idea what I should replace it with?
Thanks.

Hi Demian

It is a 0.047 nF capacitor, but the voltage code 2N is not a official EIA voltage code. So it could be somewhere between 100 VDC and 1000 VDC. You have to check some other component markings that sits around it as the part of the same circuit and see what their voltage rating is to find a proper one.

But given the low capacitance, it could be 1000 VDC rated. Or even higher if it part of the high voltage supply for the back light. But EIC code says that voltage ratings above 1000 VDC starts with 3 and not 2.

Kind regards

337. Jose Vazquez says:

Hello
I have a capacitor marked with: M474K1025 and below 550 MFF.
My question is what voltage is, and why I can replace it.
I send you a pic.

Thank you.
Pepe

Hi Jose Vazquez

You need a Metallized Polypropylene Film Capacitor (MKP) with a capacitances of 0.47 uF and I guess that the voltage rating is 550V, so since it blew up maybe pick one with a higher voltage specification.

You can also look at other components around the capacitor to get a better understanding of what voltage it might be rated for.

Kind regards

339. Jose Vazquez says:

340. Bas says:

Hi there,

How would I rate these in uF?

Hi Bas

805 is 8 uF and 246 is 24 uF

Kind regards

342. Vijay says:

Nice explanation

343. NIRAJ KUMAR says:

I m trying to copy an amplifying board. I got stuck with these three polyester capacitor.
So, i need your help to check whether i m correctly reading the value of capacitor or not. please let me know.
1. m250 47nJ means 250V 47 nF 5% tolerance
2. CY3A 221J means 1000VDC 220pF
3. 224J 100ME means 220uF 100VDC
Also. can u check Capacitor “1” is m250 470j or m250 47nJ . which one ?

Thanks a lot.

Hi Niraj

1. You got them all right, the 47n is for 47 nF, J is the tolerance.
2. I don’t think its 1000 VDC rated, just the small size and distance between legs tells me it must be in the range of the others, like 100-250V.
3. This is 224 = 0.22 uF ~ 220 nF

Kind regards

345. K.s.Dr.zoysa says:

Very essential capacitance values help for beginers .if you can show codes like 105j 335j 822j125j and values of that is great help,How ever millions thanks.ZOYSA.

346. Kike says:

Sup! I have a capacitor reading MIAL 4700j
It’s silver, cylindrical shaped… about 7mm large and 3mm thick…
Am looking for a .047uf, do I have the correct cap?

Hi Kike

I think it could be a 4.7 nF capacitor with 5% tolerance.

Kind regards

348. kris says:

I am searching for electrolitic aluminium capcitor:
100
35s
1L2

any clue?

349. Ajith says:

I want to know what is the minig of
2v155kz capacitor full minig

Hi Kris

That is a 100 uF electrolytic capacitor rated for 35 V

Kind regards

Hi Ajith

That is a 1.5 uF 10% tolerance 350VDC capacitor.

Kind regards

352. Foxcap says:

Best site for Capacitor.

353. Aman bharti says:

Very good information, I have a question. A metallized film capacitor code is CBB22 474j 400v. What is exact meaning of these name. Please Reply

Hi Aman bharti

CBB22 is the manufacturers name for the capacitor series, it is a 0.47 uF capacitance with 5% tolerance and a 400V maximum voltage rating.

Kind regards

355. tony says:

Hi please, can someone help me find something to replace this 470nj Cap
a UK supplier would be good as in a rush, it says 470nJ on the cap is this a code or does it mean the same as 0.47uF? presume 63v is the voltage rating.

Hi Tony

Farnell, RS Components or Mouser can deliver from day to day. But it will cost you.

You are right, it is 470 nF / 0.47 uF at 63V

Kind regards

357. Tony Arnold says:

I HAVE A CAPACITOR TO REPLACE =
100J X 400V
I assume this = 10pf X 5‰ X 400V
Many thanks
Tony
Tony Arnold
tony@arnys-shack.com

358. Kamil Metze says:

Markings: 1J MEF 400

Hi Kamil

That is a 100 nF, 400 VDC capacitor, 5% tolerance.

Kind regards

360. prince da_je says:

In my lg tv d bosta capacitor(450v1000uf) is faulty n is hard 2 get so what capacitor can use in replacin it

Hi Prince da je

A electrolytic capaitor with ratings of 450V and 1000 uF should not be hard to get, but generally you can replace it with any 1000-1500 uF capacitor with a voltage rating higher than 450V.

Kind regards

362. Muzammil Khatri says:

Dear Sir,

Best Regards,

Muzammil.

363. Venkata R Reddy says:

Hi guys,
I am using an AC capacitor of 100 uF, 250 V, 50 Hz. When I am using the capacitor in RC series and parallel, the following are the shape of the currents. My aim is to connect RLC in parallel with the resonant circuit.

Hi Muzammil Khatri

106 is 10 uF.

Kind regards

365. Muzammil Khatri says:

Thank you for your kind update. My fluke multimeter is reading only 1.45uF when I measure this 106k capacitor. Will get it replaced with 10Uf. Your support is highly appreciated!

Best Regards,

Muzammil.

366. Noel says:

I am looking for a 106mic 500 volt orange capppy. It looks like it was filled with alluminium. Looking at you code I think it is 2H 106M.
Is this correct and where can I find one in Australia. Thank.

367. Giles says:

Please could you tell me what type of capacitor this is and if replacing both would sort out my ceiling fan humming and low speed issue? There appear to be 2 of these yellow type capacitors but I don’t know what type they are to try and source replacements. The one is: 2.0μF 400VAC -25-70°C and the one behind it is 1.5μF 400VAC -25-70°C – are these polypropylene film capacitors by any chance?

Hi Giles

Yes, these are most likely polypropylene film capacitors, but whether they are MKP or MKT is hard to say.

Is the fan a 3 phase type using capacitors for emulation of the 3rd phase, when supplied with hot and neutral? I would think that the fan itself has failed due to wear, dirt in ball bearings, dried out lube or damaged windings in the motor.

Kind regards

369. Merrill Burton says:

Hello Mads, [1970s] motorcycle ignition box,ac voltage operation from a genorater,range unsure, bike is 12v Kawasaki.
Circuit board has 5x638B, 1x12DC, 1X135B, also 2x resistors I know the value off.
No visible + or – marks although the ID marks on three face one way and four of them face the other way.They are dark green dics about 12mmx5mm.
Can you ID these for me please. Regards Merrill.

Hi Merrill Burton

I looked at a few motorcycle rectifier/regulator schematics and I do not think there is capacitors present. It might be TVS to suppress too high transients from the generator?

If it is capacitors with diodes, they could be used as a voltage doubler/trippler.

Kind regards

371. Etienne Lessard says:

First thank for your article it’s very useful!
I have a question regarding a capacitor that blowup and it seen to not use standard code;

XR-104
PPS 800

The capacitor is from a power supply running on the 240v

Hi Etienne Lessard

Thank you 🙂

That is a metallized film capacitor, most likely a MKT or MKP type.

I guess its 0.1 uF at 800VDC rating, which corresponds to each size.

Kind regards

373. Tony says:

Hello
I need a cap for a model engine ignition circuit. 0.8 to 1uF – 400V or greater I am very limited for space. Can you advice what the smallest physical sized cap is available in that range.

Hi Tony

As it is such a high voltage, the high density capacity technologies as Tantalum is out of the question. If you can do with polarized capacitor use a electrolytic capacitor else use a MKP/Polypropylene capacitor.

Kind regards

375. Dev Raut says:

Thank you

376. Joe says:

i have MEX/TENTA MKP 0.1uf K X2 275v when testing with multimeter it says 33 nf can i replace it with MEX/GPF 0.1uf X2 275v when test this with multimeter it says 100 nf, i dont know if both r the same or not, thanks.

Hi Joe

It sounds like your original capacitor is damaged, so changing it to a healthy capacitor with the same specifications from the markings is the correct thing to do.

Kind regards

378. Trevor Allen says:

I am trying to restore an old Monochrome Ferguson 8430 tv. I have found a Blown
capacitor with a small hole blown in the very top of the case.
The Capacitor is labelled
LCR 3300 JY
I can not find anything like it for a replacement.
Can you offer me any help please.
Regards
Trevor

Hi Trevor

Your best bet is to find a identical in the TV set and measure it. To me it looks like a old first generation tantalum capacitor and then I would guess its rated for 3.3uF.

Since it is already burned, have you tried to smash it open just to be sure its not a inductor? Maybe its a 3300uH inductor.

JY is a tolerance and voltage code, unfortunately not a standard one and I would only guess for it to be lower than 100 VDC, so if you use a new component at that or greater you should be covered in.

Kind regards

380. Trevor Allen says:

Thank you very much for your help, I shall open it up and see what’s inside, it had not occurred to me that it might be an inductor, I might get it x rayed first.
On the circuit board of the Ferguson 3840 ( not 8340 ) as I first told you, the Tantalums are all marked on the board with the Polarity but this type are marked with a circle and a short line to the other lead, I suppose this maybe a strange way of marking the neg lead, but as all the Tants are all marked with a (+) it seems a bit strange.
Unfortunately I do not have a Schematic and I am in the process of trying to draw one.

Thank you very much for your valued help, I will let you know of my findings.
Kind Regards
Trevor

381. Murdy says:

Null

382. S.R.CHANDRASHEKAR says:

What is the difference between .1k63 and .1m63 box type capacitor.

Hi S.R.CHANDRASHEKAR

They are the same, 0.1uF/63VDC, K is 10% tolerance and M is 20% tolerance.

Kind regards

384. beneesh says:

Hi beneesh

Given the small size and its high voltage rating, that is a ceramic 2000 V 68pF capacitor.

Kind regards

386. beneesh says:

hello sir please suggest anyother replacement capacitor for 68pf 2kv because i cant find one in market only 1kv or 3kv is available which one would be better?

387. Soenke says:

Hi, I think I have to replace this one.
PHS 233J 1000v

Should be 22nF, right?

But what is the PHS for?

Can’t find this one as a spare part. Only other ones with 22nF /1000v
But I am not sure if the PHS is important.

388. Antoine abboud bou madi says:

Hi very good thanks

Always choose one with a higher voltage rating, a lower would get destroyed.
Kind regards

Hi Soenke

PHS is just the manufacturers product code, do not worry about that, as long as you get the capacitance, tolerance and voltage correct, according to 233j 1000V, you are fine 🙂

Kind regards

391. Devendra patil says:

I want 22J/400v capacitor. So which is Available in Indian market….

392. Beneesh says:

Can I replace a ceramic disc capacitor with and smd multilayer capacitor

393. mike jason says: